Scania EMS fault codes
All 2.348 Scania EMS (Engine Management System) diagnostic trouble codes, with meaning, causes and how to fix them.
Control units:
EMS LCS1EMS S6EMS S6 (EMS S6 EuroIII)EMS S6 IoM singlespeed (S6IM)EMS S7EMS S8EMS S8 (S8PDE)EMS10
Showing 61–120 of 2.348 codes
- 256hex 0100 Intake air mass flow sensor T126
- 257hex 0101 Intake air mass flow sensor T126
- 258hex 0102 Mass flow sensor
- 259hex 0103 Mass flow sensor
- 261hex 0105 Charge air pressure sensor T122
- 262hex 0106 Charge air pressure sensor T122
- 263hex 0107 Charge air pressure sensor
- 264hex 0108 Charge air pressure sensor
- 266hex 00010A Engine Intake Manifold #1 Pressure, sensor plausible low.
- 267hex 00010B Engine's first intake manifold, low charge air pressure
- 268hex 00010C Ambient (T202) and Boost (T122) pressure sensors do not correlate.
- 269hex 00010D Charge air pressure sensor, short circuit
- 270hex 00010E Engine Intake Manifold #1 Pressure, sensor plausible high.
- 272hex 000110 Exhaust gas pressure sensor 2, (T271), high exhaust gas pressure
- 273hex 0111 Charge air temperature
- 274hex 0112 Charge air temperature sensor
- 275hex 0113 Charge air temperature sensor
- 276hex 0114 Sensor for intake air pressure and temperature T4000
- 277hex 0115 Coolant temperature sensor T33
- 278hex 0116 Coolant temperature sensor T33
- 279hex 0117 Coolant temperature sensor T33
- 280hex 0118 Coolant temperature sensor T33
- 282hex 00011A Engine Exhaust Pressure 2 too high at idle
- 283hex 00011B Engine Exhaust Pressure 2 too low at idle
- 289hex 0121 Throttle actuator M34
- 290hex 0122 Throttle
- 291hex 0123 Throttle
- 292hex 000124 Throttle actuator supply, break in circuit
- 296hex 0128 Coolant temperature
- 304hex 0130 Lambda sensor T137
- 305hex 0131 Lambda sensor T137
- 306hex 0132 Lambda sensor T137
- 307hex 0133 Lambda sensor T137
- 310hex 0136 Lambda sensor T154
- 311hex 0137 Lambda sensor T154
- 312hex 0138 Lambda sensor T154
- 313hex 0139 Lambda sensor T154
- 320hex 000140 Post injection ontime too short, cylinder 1.
- 321hex 000141 Post injection ontime too short, cylinder 2.
- 322hex 000142 Post injection ontime too short, cylinder 3.
- 323hex 000143 Post injection ontime too short, cylinder 4.
- 324hex 000144 Post injection ontime too short, cylinder 5.
- 325hex 000145 Post injection ontime too short, cylinder 6.
- 326hex 000146 Post injection ontime too short, cylinder 7.
- 327hex 000147 Post injection ontime too short, cylinder 8.
- 340hex 000154 PM-sensor T270 - PM-sensor fails to enter regeneration state
- 341hex 000155 PM-sensor T270 - PM-sensor fails to enter measurement state
- 352hex 000160 PM-sensor T270 - PM-sensor does not maintain the temperature during regeneration
- 353hex 000161 PM-sensor T270 self test on sensitivity - High
- 354hex 000162 PM-sensor T270 self test on sensitivity - Low.
- 361hex 0169 Fuel adaptation
- 362hex 00016A Timeout error on CAN message PSABC2 from Brake System.
- 363hex 00016B Checksum error on CAN message PSABC2 from Brake System.
- 364hex 00016C Counter error on CAN message PSABC2 from Brake System.
- 368hex 000170 Steering wheel switch for cruise control, CAN messages missing
- 369hex 000171 Steering wheel switch for cruise control, CAN messages missing
- 370hex 000172 Steering wheel switch for cruise control, CAN messages missing
- 371hex 000173 Irregular misfiring on cylinder 3
- 372hex 000174 Steering wheel switch for cruise control, CAN messages missing
- 373hex 000175 Steering wheel switch for cruise control, CAN messages missing